Новые поступления

GSM / GPRS Shield Wireless Extension Board Module for Arduino gsm gprs shield sim900 module development board for arduino white
GSM / GPRS Shield Wireless Extension Board Module w/ Antenna / Adapter for Arduino
2624.15 RUR
SIM900 Quad-band GSM GPRS Shield Development Board For Arduino gsm gprs shield sim900 module development board for arduino white
SIM900 Quad-band GSM GPRS Shield Development Board For Arduino Manual download: click to open Feature: The GPRS Shield is based on SIM900 module from SIMCOM and compatible with Arduino and its clones. The GPRS Shield provides you a way to communicate using the GSM cell phone network. The shield allows you to achieve SMS, MMS, GPRS and Audio via UART by sending AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). The shield also has the 12 GPIOs, 2 PWMs and an ADC of the SIM900 module(They are all 2V8 logic) present onboard. Specifications: Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. GPRS multi-slot class 10/8 GPRS mobile station class B Compliant to GSM phase 2/2+ Class 4 (2 W @ 850 / 900 MHz) Class 1 (1 W @ 1800 / 1900MHz) Control via AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal). Embedded TCP/UDP stack - allows you to upload data to a web server. RTC supported. Selectable serial port. Speaker and Headphone jacks Low power consumption - 1.5mA(sleep mode) Industrial Temperature Range - -40C to +85 C Application: M2M (Machine 2 Machine) Applications. Remote control of appliances. Remote Weather station or a Wireless Sensor Network. Vehicle Tracking System with a GPS module. Cautions: Make sure your SIM card is unlocked. The product is provided as is without an insulating enclosure. Please observe ESD precautions specially in dry (low humidity) weather. The factory default setting for the GPRS Shield UART is 19200 bps 8-N-1. (Can be changed using AT commands). Power select - select the power supply for GPRS shield(external power or 5v of arduino) Power jack - connected to external 4.8~5VDC power supply Antenna interface - connected to external antenna Serial port select - select either software serial port or hareware serial port to be connected to GPRS Shield Hardware Serial - D0/D1 of Arduino Software serial - D7/D8 of Arduino Status LED - tell whether the power of SIM900 is on Net light - tell the status about SIM900 linking to the net UART of SIM900 - UART pins breakout of SIM900 Microphone - to answer the phone call Speaker - to answer the phone call GPIO,PWM and ADC of SIM900 - GPIO,PWM and ADC pins breakout of SIM900 Power key - power up and down for SIM900 Note: The SIM900 Board Input is 5-26V 2A,We Recommended current is more than 9V 2A Ensure your SIM card is not locked GPRS Shield Communication baud rate is 19200 BPS 8-N-1 Package included: 1 x SIM900 Board for Arduino
24.5 RUR
3G 3DBI GSM GPRS PCB Antenna With IPEX Interface For GSM Module Arduino SIM900 GPRS Shield gsm gprs shield sim900 module development board for arduino white
3G 3DBI GSM GPRS PCB Antenna With IPEX Interface For GSM Module Arduino SIM900 GPRS Shield
115.05 RUR
GSM / GPRS Shield SIM900 Module Development Board for Arduino - White gsm gprs shield sim900 module development board for arduino white
1. Hook your Arduino up to GSM/GPRS cell phone network with GPRS shield! You can use your Arduino to dial a phone number or send a text to your friend. 2. Features: GSM/GPRS module SIM900; Supports frequency band 850/900/1800/1900MHz; Support TCP/UDP protocols; Full control via AT commands set: Standard - GSM 07.07 & 07.05 and Enhanced - SIMCOM AT Commands; Power supply: 5~12V; I/O voltage: 2.8V; Default baud rate: 19200; The highest baud rate: 115200. 3. Applications: data transmission of Internet sensor; Automatic monitoring system; Pollution source remote monitoring; GPRS Weather information collection system; Industrial energy consumption monitoring; Warehouse monitoring management.
4019.35 RUR
Elecfreaks DIY GPRS/GSM Learning Development Set Works with Arduino Products gsm gprs shield sim900 module development board for arduino white
Brand Elecfreaks Model GPRS/GSM Starter Kit Quantity 1 Color Multicolor Material FR4 Features Easy and handy GPRS/GSM development set for beginners; Full cellphone equipment with GPRS/GSM module LCD5110 display screen and analog keyboard input module based on board compatible with Arduino panel. Specification Fully compatible with Arduino / Freaduino and Mega. Free serial port connecting you can select Hardware Serial port(D0/D1) control or Software Serial port(D2/D3) control it. SIM900 all pins breakout. Not just the UART port and debug port be layout but also all pins on SIM900 be layout to the 2.54 standard pitch. Super capacitor power supply for the RTC. EFCom not only can use the button for power on but also can use the digital pin of Arduino to power on and reset the SIM900 module. Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS multi-slot class 10/8 GPRS mobile station class B Compliant to GSM phase 2/2+ Class 4 (2 W @850/ 900 MHz) Class 1 (1 W @ 1800/1900MHz) Control via AT commands (GSM 07.07 07.05 and EFCOM enhanced AT Commands) Supply voltage range : 3.1 4.8V Low power consumption: 1.5mA(sleep mode) 1.6" display screen. Application DIY cellphone; GPRS/GSM technology leanring and development; Arduino leanring and development English Manual/Spec Yes (E-manual) Other GPRS Shield - EFCom is an ultra compact and reliable wireless module. This GPRS Shield is compatible with all boards which have the same form factor (and pinout) as a standard Arduino Board. EFCom is base on SIM900 4 Frequency GPRS module. The GPRS Shield is configured and controlled via its UART using simple AT commands. Just plug this shield on the Arduino/ Freaduino board you could easy to use AT command control EFCom shield. You can use the 2 jumper block to connect the SIM900 URAT post to any pins within D0-D3(for Hardware/Software serial port). There is a switch on board you can use it to select the connection of the UART port or Debug port even be set on on Arduino but by the switch and jumper block the SIM900 can be connect to PC via FT233RL. Fully compatible with Arduino / Freaduino and Mega; Free serial port connecting you can select Hardware Serial port(D0/D1) control or Software Serial port(D2/D3) control it; SIM900 all pins breakout. Not just the UART port and debug port be layout but also all pins on SIM900 be layout to the 2.54 standard pitch; Super capacitor power supply for the RTC; EFCom not only can use the button for power on but also can use the digital pin of Arduino to power on and reset the SIM900 module; Quad-Band 850/ 900/ 1800/ 1900 MHz; GPRS multi-slot class 10/8; GPRS mobile station class B; Compliant to GSM phase 2/2+ ; Class 4 (2 W @850/ 900 MHz); Class 1 (1 W @ 1800/1900MHz); Control via AT commands (GSM 07.07 07.05 and EFCOM enhanced AT Commands); Supply voltage range : 3.1 4.8V; Low power consumption: 1.5mA(sleep mode); Dimension:68.33x53.09mm(Same dimension of Arduino main board) Packing List 1 x Freaduino UNO for arduino 1 x ElecFreaks GPRS/GSM Shield - EFCom for arduino 1 x 100~240V US plug power adapter (92cm) 1 x 4 Frequency antenna 1 x LCD5110 1 x Analog ADKay Pad 1 x 3P connect jumper wire(20cm)
5382.04 RUR
GSM / GPRS SIM900 Module ICOMSAT Expansion Board w/ Antenna + Cable for Arduino - Blue + Black gsm gprs shield sim900 module development board for arduino white
Brand NO Model No Quantity 1 Color Black + blue Material PCB + aluminum alloy Features GSM/GPRS SIM900 module ICOMSAT expansion board compatible w/ Arduino Specification MPU: SIM900; Individual working volage and current; 5V / 2A; Must provide DC 9V / 2A power after plug Arduino board for GSM shield power on current and peak current need 2A; Quad-band GSM / GPRS: 850 / 900 / 1800 / 1900MHz; GPRST multi-slot class 10/8; GPRS mobile station class B Compliant to GSM phase 2/2+Class 4 (2 W @850/ 900 MHz); Supports UART port antenna connector; Built-in TCP / IP protocol; Supports Multi-IP connecting; Class 1 (1 W @ 1800/1900MHz); Low power consumption: 1.5mA(sleep mode); Operation temperature: -40~+85'C; The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice SMS Data and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 07.05 and SIMCOM enhanced AT Commands) and fully compatible with Iteaduino/Arduino and Mega. Application A product for arduino that works with official Arduino boards. English Manual/Spec Yes; Download address: www.veskys.com/Instrucuction Manual/0113052620384021.zip Packing List 1 x Expansion board 1 x Antenna 1 x Extending cable (17cm)
3463.34 RUR
SoaringE E00314 Wireless GSM / GPRS SIM900 Shield Development Board for Arduino - Green gsm gprs shield sim900 module development board for arduino white
The GPRS Shield is based on SIM900 module from SIMCOM and compatible with Arduino and its clones. The GPRS Shield provides you a way to communicate using the GSM cell phone network. The shield allows you to achieve SMS MMS GPRS and Audio via UART by sending AT commands (GSM 07.07 07.05 and SIMCOM enhanced AT Commands). The shield also has the 12 GPIOs 2 PWMs and an ADC of the SIM900 module (They are all 2V8 logic) present onboard. Features 1) Quad-Band 850 / 900/ 1800 / 1900MHz - would work on GSM networks in all countries across the world. 2) GPRS multi-slot class 10/8 3) GPRS mobile station class B 4) Compliant to GSM phase 2/2+ 5) Class 4 (2 W @ 850 / 900 MHz) 6) Class 1 (1 W @ 1800 / 1900MHz) 7) Control via AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. 8) Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal). 9) Embedded TCP/UDP stack - allows you to upload data to a web server. 10) RTC supported. 11) Selectable serial port. 12) Speaker and Headphone jacks 13) Low power consumption: - 1.5mA (sleep mode) 14) Industrial Temperature Range - -40~85 'C
2416.83 RUR
GSM/GPRS/GPS Shield (B) Arduino Shield Based on SIM808 gsm gprs shield sim900 module development board for arduino white
GSM/GPRS/GPS Shield (B) Arduino Shield Based on SIM808
2976.81 RUR
FreArduino GSM / GPRS Shield Expansion Board for Arduino (Works with Official Arduino Boards) gsm gprs shield sim900 module development board for arduino white
Color: Black - Quantity: 1 - Material: Semi-fiberglass board FR4 - Compatible with Freaduino / Arduino / Mega2560 - Frequency: 850 / 900 / 1800 / 1900MHz - Power: 5V - Great for GSM / GPRS cell phone DIY lovers - Suitable for wireless project development and remote control development - Packing list: 1 x Expansion board
3266.76 RUR
Itead GSM / GPRS SIM900 Module Development Board GBoard Integrated Learning Board for Arduino gsm gprs shield sim900 module development board for arduino white
Overview Gboard is a unique Arduino board which features a SIM900 GSM/GPRS module an XBee socket nRF24L01+ module interface and an ATMega328P controller. This board will add wireless XBee / nRF24L01+ control as well as GSM/GPRS connectivity to your projects. It’s great for anything from home automation to robot control. The possibilities are endless! Gboard can be used as a GSM/GPRS data transfer or wireless communication project development platform. Gboard support wide range power supply and Micro SD for mass storage. There are some 3pin electronic brick/ sensor brick interface breakout on board it offer an easy way for a quick prototyping. The board requires FTDI basic board to upload sketch you can use our Foca board to do it. Gboard can be powered by a mini USB power Jack. Hardware UART Setting Jumpers The SIM900 module and XBee module communicate to ATMega328 through UART. They cannot be used with the same port at the same time so there are two UART setting jumpers to configure the UART communication. The figure of UART setting jumpers is as below. D0 and D1 are hardware UART ports of Arduino. D2 and D3 are digital GPIO of Arduino. There are two configurations to set the UART communication. Description UART Setting Jumpers Connection Hardware UART to SIM900Software UAR to Specific ST D0(Hardware Rx of Arduino)SR D1(Hardware Tx of Arduino)XT D2(Software Rx/Tx of Arduino)XR D3(Software Rx/Tx of Arduino) Software UART to SIM900Hardware UART to Specific XT D0(Hardware Rx of Arduino)XR D1(Hardware Tx of Arduino)ST D2(Software Rx/Tx of Arduino)SR D3(Software Power and reset connection of SIM900 In the GBoard the PWRKEY and RESET pins of SIM900 module connect to Arduino as list below. Arduino pin SIM900 pin Enable D6 PWR High level Active D7 RESET High level Active Software With embedded bootloader Gboard is easy to use by Arduino IDE through Foca series. ISP of Atmega328 is broke out for download firmware easily. Note The GBoard does not have a USB con­nec­tion. So you need a USB/Serial adapter - we recommend the Foca FT232RL breakout board.
3260.4 RUR
EFCom Pro Wireless 850/900/1800/1900MHz GPRS/GSM Module w/ Antenna - White gsm gprs shield sim900 module development board for arduino white
Model N/A Quantity 1 Color White Material FR4 half glass fiber board Features EFCom Pro is a 4 frequency GPRS module supports 850/900/1800/1900MHz; Supports all the functions on cell phone such as sending SMS making call fax etc. You will learn fast about development process of cell phones and processing wireless development with this module Specification A type of GSM/GPRS Integrated single chip base on SIM900; Adopt ARM926EJ-S; Power supply: 5V; Fully compatible with AVR/Arduino/ARM/FPGA development board Application Great for DIY projects Packing List 1 x Module 1 x Antenna 4 x Copper cylinder
3143.98 RUR
GSM / GPRS Shield Wireless Extension Board Module w/ Antenna / Adapter for Arduino gsm gprs shield sim900 module development board for arduino white
Model SHD-EFCOM Quantity 1 Color Black Material FR4 Features Arduino Compatible GSM / GPRS Shield Application for Arduino experiment and DIY projects Other Fully compatible with Freaduino/Arduino and Mega 2560 Quad-Band 850/ 900/ 1800/ 1900 MHz voltage: 5V Size: 68.33 x 53.09mm Packing List 1 x GSM / GPRS Shield 1 x Quad-Band wireless antenna 1 x 100~240V Power adapter ( 100cm-cable / US plug)
3009.11 RUR
Simcom SIM900 GSM / GPRS Module Quadband 850 / 900 / 1800 / 1900 MHz for Arduino GPRS Module - Green gsm gprs shield sim900 module development board for arduino white
A product for Arduino that works with official Arduino boards.
1012.15 RUR
1PCS SIM900 Quad Band GSM / GPRS module New gsm gprs shield sim900 module development board for arduino white
1PCS SIM900 Quad Band GSM / GPRS module New
1126.03 RUR
SD / TF Card Shield Slot Reader Expansion Board Module for Arduino gsm gprs shield sim900 module development board for arduino white
SD / TF Card Shield Slot Reader Expansion Board Module for Arduino
259.58 RUR
GSM GPRS SIM900 1800MHz Short Message Service m590 SMS Module DIY Kit For Arduino gsm gprs shield sim900 module development board for arduino white
GSM GPRS SIM900 1800MHz Short Message Service m590 SMS Module DIY Kit For Arduino Specification: Voltage: 5V Frequency: 900 1800 MHz Stand by current: < 10 mA Working current: < 80 mA Baud: 9600 or change by sending AT+IPR=xxxx Interface: TTL Commands: Regular AT commands Connector: 5V GND TxD RxD Antenna: Please solder a copper wire to the board or use an IPEX socket Temperatures: -30 C to 80 C Functions: Send/receive SMS messages and GPRS data. Feature: Excellent for remote sensing, experiments, alarms and automatic data collection. The control port is a regular serial port. You may connect it directly with a microcontroller such as Arduino. Or you can use a USB to serial port adapter and send commands directly from a computer. If you also need a USB to serial adapter, please contact us. A complete instruction for using the AT commands will be provided. Package includes: 1 x DIY Kit
4.6 RUR